Such a Little Part (Climate Control Resistor)

You expect your heater/air conditioner to work like it should.  You have a control for temperature and one for fan speed.  You even have a control for what vents the air comes out of. 

Don't be surprised one day if your blower fan develops a mind of its own and starts going crazy.  Most of the time, you may find that it starts blowing at full speed, and nothing you do to try to control it does any good.  This is what may be happening.

Your blower motor has an electronic component called a resistor.  It does what its name says; it offers resistance.  When you want the fan to run more slowly, you turn the fan speed down.  That resistor accomplishes that by turning its resistance up.  When the resistor fails, the power has nothing to slow it and the fan speeds up. 

It's a small part and can fail due to age or corrosion.  It's usually not an expensive part, either, but it's often found in a location that's not that easy for the technician to get to.  That means labor costs will vary depending on the design of your vehicle. 

Occasionally, a faulty resistor can cause the blower motor not to work at all or only partially come on.  But other things can cause that as well, such as a faulty fan switch or vent control. 

This is where a technician's training comes in.  Special equipment can track down precisely where the issue is so you can be assured the correct part is being replaced.

It's just not pleasant when the blower motor isn't following orders.  Have your service facility check it out so you can be the blower's boss, like it should be. 

Spring Street Automotive Inc
1701 Spring Street
Quincy, IL 62301
217-228-9141
http://www.springstreetauto.com

Have a Ball! Know your Ball Joints (Ball Joints)

We all have joints in our own skeletal system, but did you know your vehicle has some joints of its own? One of the most important is called a ball joint.

One of the interesting things is that it's somewhat similar to the ball and socket joints we have in our hips and shoulders.  A ball joint allows two parts it joins together to move in more than one direction at the same time.

Think about your wheels.  They have to move up and down when there are bumps in the road but in sideways directions when you are making a turn. As you can see, the ball joints are important for your steering and handling to work correctly.

Since ball joints do so much, they can wear out and become loose.  When the ball wears down or the socket gets worn, there can be too much play in them.  It can get so bad that the ball can come out of the socket and your wheel can fall off, a dangerous situation.  Ball joints can also seize up.  Some of them are sealed and never require maintenance; others require periodic lubrication.

Here are some signs that your ball joints are going bad:

• Your vehicle pulls to one side
• You can hear a clunking noise coming from a wheel area
• Your tires are wearing unevenly, especially on the inside

The earlier a failing ball joint is discovered, the better. The best way is to have regular inspections by a technician.  Your service facility will periodically check ball joints at intervals recommended by the manufacturer. The cost to replace them can vary widely depending on whether you have a vehicle with a 2-ball or 4-ball configuration.  Also, sometimes just the joints can be replaced, but other times they are part of a larger control arm assembly that has to have all the parts replaced at the same time. 

Your vehicle's proper steering, handling and tire wear all contribute to a better, safer driving experience.  Make sure your ball joints are up to the job.

Spring Street Automotive Inc
1701 Spring Street
Quincy, IL 62301
217-228-9141
http://www.springstreetauto.com

Passing the Test (How to Prevent Emissions Test Failure)

Vehicle emission testing has become ubiquitous in North America and for a good reason.  Clean air quality is important for the environment and all of us.  Since vehicle emissions are among the main causes of air pollution, emission testing can alert you to problems in your vehicle than can be fixed so it won't needlessly pollute.

Emissions tests are looking for certain toxic gases internal combustion engines produce, such as nitrogen oxide, particulate matter, non-methane organic gases and formaldehyde.  Emissions control systems reduce these gases if they are working properly. 

The best way to minimize pollution is to keep those vehicle systems working properly, and periodic inspection and maintenance is the key.  So if you want to make sure your vehicle will pass an emissions test, it helps to know what might go wrong.

Let's start on the easy one.  Your gas cap could be loose, allowing vapors to escape into the atmosphere.  The most common solution is to replace it.  Or your air filter may be dirty.  A dirty air filter may push your hydrocarbons pass the acceptable level.

Now to the more complicated things.  The mixture of fuel and air in your engine may be tilted toward the "too much fuel" side.  That could cause problems for your vehicle's catalytic converter, a device that converts toxic gases from your exhaust into less toxic pollutants.

Your vehicle has a closed system that prevents fuel tank vapors from escaping into the air; it's called the EVAP system.  A technician can track down problems.

Vehicle engineers have gone to great lengths to minimize the amount of pollution your vehicle produces.  Your vehicle's manufacturer recommends how frequently those systems need servicing.  Keep those systems in good shape and you're likely to pass emissions tests with flying colors.  Neglect them and you might find your vehicle failing an emissions test.  When that happens, you'll have to get the problems repaired before you can get back on the road.

Spring Street Automotive Inc
1701 Spring Street
Quincy, IL 62301
217-228-9141
http://www.springstreetauto.com